XP95

The XP95 range of analogue addressable fire detectors uses tried and trusted technology to give the best performance, and has unique features that benefit the installer and the end user. It is suitable for medium-to-large applications with simple installation requirements. As it operates using digital communication, XP95 has a high immunity from corruption, and is, therefore, often preferred in a large system where life safety is critical. XP95 products are frequently used in commercial, industrial, financial, government, IT/telecoms and healthcare applications.

XP95 Optical Smoke Detector

The XP95 Optical Smoke detector uses an internal pulsing infrared LED and a photo-diode at an obtuse angle. In clear air conditions the photo-diode in the XP95 detector receives no light from the LED and produces a corresponding analogue signal. The signal increases when smoke enters the chamber and light is scattered onto the photo-diode. The optical smoke detector has a clear indicator LED which emits red light when the detector is in alarm.

XP95 Multisensor Detector

The XP95 Multisensor Detector contains an optical smoke sensor and a thermistor temperature sensor whose outputs are combined to give the final analogue value.

XP95 CS Heat Detector

The XP95 Heat Detector monitors temperature by using a single thermistor which provides a count output proportional to the external air temperature. The XP95 range features two heat detectors, standard and high temperature. The standard heat detector is classified as an A2S device and will report an alarm at 55°C. The high temperature detector, classified as a CS device, will report an alarm at 90°C.

XP95 A2S Heat Detector

The XP95 Heat Detector monitors temperature by using a single thermistor which provides a count output proportional to the external air temperature. The XP95 range features two heat detectors, standard and high temperature. The standard heat detector is classified as an A2S device and will report an alarm at 55°C. The high temperature detector, classified as a CS device, will report an alarm at 90°C.

XP95 VAD Base with Isolator

The XP95® Visual Alarm Device (VAD) Base incorporates a loop-powered VAD with a standard mounting base. It is used to signal a visual fire alarm warning in enclosed areas. The XP95 VAD Base can be used either with a detector fitted or with a cap for operation as a stand-alone alarm device. The VAD Bases are supplied with a built-in isolator. A version without an isolator is also available.

Multi Tone Open Area Sounder

The Multi-Tone Open-Area Sounder is designed for use in open areas and can be connected to any Discovery or XP95 system

XP95 Multisensor Detector

The Intelligent Open-Area Visual Indicator has been developed for use in situations where there is a risk that sounders will not be heard.

CAT C Loop Powered VAD 8M

The Loop Powered VAD is designed for indoor use. The Category C VAD is specifically designed for use on a ceiling and comes in two different coverage classes. The two EN 54-23 coverage classes are C-3-8.5 and C-3-15. These devices are used to supplement sounders in areas which carry the risk that sounders will not be heard.

CAT C Loop Powered VAD 15M

The Loop Powered VAD is designed for indoor use. The Category C VAD is specifically designed for use on a ceiling and comes in two different coverage classes. The two EN 54-23 coverage classes are C-3-8.5 and C-3-15. These devices are used to supplement sounders in areas which carry the risk that sounders will not be heard.

Intellegent Manual Call Point

The Intelligent Manual Call Point has been designed to operate on a loop of intelligent fire detection devices. An alarm is initiated by pressing the resettable element. The manual call point signals to the Control and Indicating Equipment using an interrupt feature within the Apollo Digital Protocol. An alarm status is indicated through the rotation of the resettable element, displaying yellow and black indication bars and a solid red LED. The manual call point can be easily reset from the front using the supplied reset key.

Intellegent Manual Call Point

The Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95, Discovery and CoreProtocol systems.

Intellegent Input / Output Unit

The Intelligent Input/Output Unit provides supervision of one or more normally open contacts connected to a single pair of cables and a set of changeover relay output contacts.

Intellegent Twin Switch Monitor

The Intelligent Twin Switch Monitor provides the function of two Switch Monitor units within one enclosure. The two units are electrically independent of each other. There is a DIL switch on each unit to set the address. Both Switch Monitor units in the enclosure are designed to monitor the state of one or more single pole, volt-free contacts connected on a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flow switches.